PPPoE users usually have DSL cable modems.Ĥ )If you choose L2TP, enter the username and password and choose the Secondary Connection provided by your ISP. Dynamic IP users are usually equipped with a cable TV or fiber cable.Ģ )If you choose Static IP, enter the information provided by your ISP in the corresponding fields.ģ )If you choose PPPoE, enter the username and password provided by your ISP. Parameters on the figures are just used for demonstration.ġ )If you choose Dynamic IP, you need to select whether to clone the MAC address. Since different connection types require different cables and connection information, you can also refer to the demonstrations in Step 4 to determine your connection type.Ĥ.Follow the instructions on the page to continue the configuration. If you are unsure of what your connection type is, click Auto Detect. You can also modify the settings according to the service information provided by your ISP.įollow the steps below to check or modify your internet connection settings.ġ.Visit, and log in with your TP-Link ID or the password you set for the router.ģ.Select your internet connection type from the drop-down list. In this part, you can check your current internet connection settings. Then follow the instructions to bind the router to your TP-Link ID.Ģ. Then follow the step-by-step instructions to connect your router to the internet.ģ.To enjoy a more complete service from TP-Link (remote management, TP-Link DDNS, etc.), log in with your TP-Link ID or click Register Now to get one. If you need the IPv6 internet connection, please refer to the section of Set Up an IPv6 Internet Connection.įollow the steps below to set up your router.ġ.Visit, and log in with the password you set for the router.Ģ.Click Quick Setup on the top of the page. The Quick Setup Wizard will guide you to set up your router. Monitor the Internet Traffic Statistics.Backup and Restore Configuration Settings.Chapter 12 Customize Your Network Settings.Use PPTP VPN to Access Your Home Network.Use OpenVPN to Access Your Home Network.Make Xbox Online Games Run Smoothly by UPnP.Make Applications Free from Port Restriction by DMZ.Open Ports Dynamically by Port Triggering.Share Local Resources on the Internet by Virtual Servers.Manage the Router via the TP-Link Tether App.Configure the Router in Access Point Mode.Manually Set up Your Internet Connection.Chapter 1 Get to Know About Your Router.For more information, see How do I power cycle my home network?. After power cycling your router, repeat Steps 4-8. Note: If you have trouble connecting your mobile device to your router’s network, try power cycling your router. I’m getting a router not found error when I try to install my NETGEAR router using the Nighthawk app what do I do?Ĩ. Launch the NETGEAR Nighthawk app on your mobile device.ĩ. Follow the instructions in the Nighthawk app to install your router and connect to the Internet.I’m getting an Internet not connected error when I try to install my NETGEAR router using the Nighthawk app what do I do?.How do I turn off mobile data on my smartphone if I get an error during installation?.Note: If you encounter any errors while attempting to connect to your router, see the following articles for troubleshooting information: Connect your mobile device to the network that is listed on your router's label and enter the password.On your iOS or Android mobile device, tap Settings > Wi-Fi.The label is on the back or bottom of your router. Look on the router label for your router's WiFi network name (SSID) and network key (password).Attach the provided antennas (if any) and connect your modem to the Internet port on your router.To set up and install your NETGEAR router using the NETGEAR Nighthawk app: For more information, see How do I set up my NETGEAR router using the router web interface?. If you prefer to install your router using a computer, or if your product is not supported, you can also set up your router from the router's web interface. To see if your product supports the Nighthawk app, see Which products support the NETGEAR Nighthawk app?. You can also use the Nighthawk app to view the devices on your network, run speed tests, and manage your WiFi settings. The Nighthawk app is the easiest way to set up your NETGEAR router.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |